Change engine oil every time after 15,000 km
If the mileage was 15,000 km earlier than in one year, then you need to start changing the engine oil. If the oil change is due only a few months before the Annual Inspection, then it is recommended to combine both of these inspections.
Description of work steps
Engine oil: change (incl. oil filter replacement).
Draining water from the fuel filter (diesel engine).
Control of the thickness of the brake linings of the disc brakes of the front wheels.
Reading from the memory of malfunctions of the automatic control system of all systems.
Resetting the maintenance interval indicator.
After every oil change
Enter the due date for the next inspection (maximum after 1 year / 15,000 km) into a sticker "Next inspection" and stick it on the side of the dashboard (from the engine side).
Filling out "Maintenance hang tag", hang it on the interior rearview mirror.
Annual inspection (every 12 months)
Every 2 years - brake fluid change (additional operation).
Every 2 years - change the air filter element and clean the filter housing (additional operation).
Every 3 years - coolant change (additional operation).
Emissions Control: Validity - See Emissions Control badge on license plate.
Vehicles with high mileage - change the oil no later than 15,000 km. A premature annual inspection must be carried out no later than 30,000 km.
Recommended: Replace the wiper blades.
Description of work steps
Reading from the memory of faults of all systems.
Engine check for leaks and damage.
Engine oil change, oil filter change.
Fuel filter: Water drain (diesel engines).
Changing the air filter element and cleaning the filter housing (every 2 years) (vehicles with less than 60,000 km mileage in two years).
Visual inspection of external damage to the airbag module "Airbag".
Resetting the maintenance interval indicator.
Check the brake system for leaks and damage.
Control of the thickness of the brake linings.
Check for leaks and damage to the gearbox, drive shafts and protective covers of the hinges.
Lower arm trunnions: Check for leaks and damage to protective covers.
Tie Rod Ends: Gap control and seal boot fastening.
Tire pressure monitoring (incl. spare wheel) and if necessary, swap.
Tire wear pattern monitoring (incl. spare wheel).
Tire tread height monitoring and recording (incl. spare wheel) (PL..., PP..., ZP..., ZL..., RESERVE.).
Check for leaks and damage to the exhaust pipe.
Checking the brake fluid level and, if necessary, topping up.
Brake fluid change (every 2 years).
Control of frost resistance of the coolant, tightness of the cooling system and, if necessary, refueling with coolant.
Coolant change (every 3 years).
Battery: Check the electrolyte level and, if necessary, top up with distilled water.
Checking the waterproof housing for contamination and cleaning if necessary.
Door stops: Lubricate.
Checking the operation of lamps, signaling devices, direction indicator lamps and signal lamps, 10 warning light signaling by means of headlights, horn.
Windshield wipers: Control of operation, condition of rubber brushes Windshield washers:
Control of work, if necessary - regulation of the jets or topping up the liquid.
Headlights: Control and, if necessary, adjustment.
After every inspection
Enter the date of the next inspection in the sticker "Next inspection" and stick it on the side of the dashboard (from the engine side).
Trial run incl. testing of foot and hand brakes, steering and gear shifting. Final control.
Filling out "Maintenance hang tag", hang it on the interior rearview mirror.
Annual inspection (every 12 months)
Includes: Annual inspection and additional operations listed below.
Description of work steps
Three-phase alternator V-belt: Condition and tension control.
Fuel filter: Change (diesel engine vehicles).
Transmission oil: Checking the oil level and topping up if necessary (Manual Transmission).
Control of the integrity of the protective coating of the bottom of the body.
Cleaning the sliding sunroof guide rails and spraying them with silicone grease.
Dust and pollen filter for the passenger area: change (if it is installed).
Every 60,000 km
Includes: Inspection every 30,000 km and additional operations listed below.
Description of work steps
Spark plugs: replace.
Air filter: Cleaning the housing and changing the filter element (every 2 years) (vehicles with less than 60,000 km mileage in two years)..
Power steering: Control.
Every 90,000 km
Includes: Inspection every 30,000 km and additionally the operation listed below.
Description of work steps
Toothed belt for camshaft drive (cam) Shaft: Replacement (only for engines "TDI").