Interior (internal body elements) Skoda Rapid 1

Center floor console — appearance
1. Cup holder 2. Mounting screw, installation torque 1.5 Nm 3. Parking brake handle 4. Center floor console assembly 5. Additional capacity 6. Lid

Removal and installation of the center console
Removing 1. Turn off the ignition and all electrical consumers. 2. To remove the panel of facing of the lever of a gear change. 3. Remove armrest assembly (if the car is equipped). 4. Remove cover (6), shown in the...

Removing and installing the center console mounting bracket
Removing 1. Remove the center floor console assembly (for details, see the relevant section in this chapter). 2. Loosen the fastening nuts (1), shown in the figure below. 3. Remove mounting bracket (2) center floor...

Removal and installation of an armrest
Removing 1. Disconnect from the latches and remove the side covers with the support axles of the armrest (1) And (3), as shown in the figure below. 2. Loosen the fastening nut (4), pull up and remove the armrest...

Dashboard assembly — appearance
1. Dashboard assembly 2. Fastening screw, tightening torque 1.5 Nm

Removal and installation of the instrument panel assembly
Removing Note. Disconnect the negative terminal from the battery first. 1. Remove driver's airbag module (for details, see the relevant section in chapter Passive safety ). 2. Remove steering wheel assembly (for...

Glove box — removal and installation
Removing 1. Remove the dashboard side cover on the passenger side. 2. Unscrew the fastening screws shown in the figure below by arrows. The tightening torque of the fastening screws during installation is 1.5 Nm. 3....

Steering column trim panels — removal and installation
Removing 1. Remove the front driver's airbag module (for details, see the relevant section in chapter Passive safety ). 2. Remove steering wheel assembly (for details, see the relevant section in chapter Steering ). 3....

Dashboard support bar — removal and installation
Removing 1. Remove the dashboard assembly (more, see relevant section in this chapter ). 2. Unscrew the fastening screws (3), shown in the figure below. Tightening torque for mounting screws when installing 9 Nm. 3....

Front door trim panel — removal and installation
Removing 1. Turn off the ignition and all electrical consumers. 2. Remove trim panel (2) power window master switch as shown in the figure below. Then disconnect the wiring harness connectors (3) And (4), shown in the...

Rear door trim panel — removal and installation
Removing 1. Turn off the ignition and turn off all electrical consumers. 2. Carefully detach the panel (3) from the rear door trim panel using the special tool (Т10383, 3409), as shown in the figure below. 3. Unscrew...

C-pillar trim panel — removal and installation
Removing 1. Detach the C-pillar trim panel (1) from the door seal on the doorway, as shown in the figure below. 2. Disconnect the rear pillar trim panel from the tailgate seal. 3. Disconnect the C-pillar trim panel from...

Facing panel of the intermediate and rear pillars of the body — removal and installation
Removing 1. Remove the luggage compartment side trim panel. 2. Detach the fastening hooks (2), shown in the figure below. 3. Detach the retainer (5), shown in the figure below. 4. Disconnect the brackets shown in the...

Doorway control panels — removal and installation
Removing 1. Remove the rear seat cushion assembly (for details, see the relevant section in this chapter). 2. Remove the inner wheel arch trim panel (for details, see the relevant section in this chapter). 3. Disconnect...

Inner wheel arch trim panel — removal and installation
Removing 1. Remove the rear seat cushion assembly (for details, see the relevant section in this chapter). 2. To remove the panel of facing of the central rack of a body. 3. Carefully detach the fixing clips (2) from...

Tailgate trim panel — removal and installation
Removing 1. Unscrew the fastening screws (6) and remove the door release lever (5), shown in the figure below. The tightening torque of the fastening screws during installation is 2.5 Nm. 2. Remove the rear window wiper...

Luggage compartment door trim panel (Spaceback) — removal and installation
Removing 1. Unscrew the fastening screw (8) and remove the tailgate release lever (7), as shown in the figure below. The tightening torque of the fastening screw during installation is 2.5 Nm. 2. Disconnect the fixing...

Luggage compartment trim panels
Removal and installation of the panel of facing of a back wall of a luggage compartment Removing 1. Remove the floor covering in the luggage compartment. 2. Remove rivet-type retainers (4), shown in the figure below. 3....

Interior ceiling lining panel — removal and installation
Removing 1. Turn off the ignition and turn off all electrical consumers of the car. 2. Remove sun visors. 3. Remove the A-pillar trim panels (for details, see the relevant section in this chapter). 4. Remove the upper...

Removal and installation of a forward seat
Removing 1. Set the front seat to the most forward position using the adjusters. 2. Unscrew the rear mounting screws (1) And (3), shown in the figure below. 3. Move the front seat to its rearmost position using the...

Removal and installation of lateral covers of a forward seat
Removing 1. Remove the front seat assembly (for details, see the relevant section in this chapter). 2. Unscrew the fastening screw (1), shown in the figure below. Mounting screw tightening torque during installation: 1...

Removal and installation of lateral covers of a forward seat (seat with height adjustment)
Removing 1. Remove the front seat assembly (for details, see the relevant section in this chapter). 2. Unscrew the fastening screw (1), shown in the figure below Tightening torque when installing the fixing screw: 1 Nm....

Removal and installation of guides of a head restraint of a forward seat
Removing 1. Remove the front seat assembly (more, see relevant section in this chapter ). 2. Remove the front seat belt buckle (for details, see the relevant section in chapter Passive safety ). 3. Remove the front seat...

Removal and installation of an upholstery of a pillow of a forward seat
Removing 1. Remove the front seat assembly (more, see relevant section in this chapter ). 2. Remove front seat buckle assembly (for details, see the relevant section in chapter Passive safety ). 3. Remove the side cover...

Removal and installation of a covering of a back and a back of a front seat assy
Removing Note. When dismantling, check the technical condition of the seat back padding. Below is a description of the removal and installation of elements using the example of the left front seat. The right front seat...

Removal and installation of a pillow of a back seat assy
Removing 1. Press on both sides of the seat cushion with your hands (1) in places of mounting elements (2), and then pull the cushion, applying the necessary force, in the direction of the arrow shown in the figure...

Removal and installation of a back of a back seat
Removing 1. Remove the rear seat belt guide (for details, see the relevant section in chapter Passive safety ). 2. Disconnect the backrest of the rear seat on both sides from the fastening elements. Lower the rear seat...

Removal and installation of a covering and stuffing of a pillow of a back seat
Removing 1. Remove the rear seat cushion assembly (for details, see the relevant section in this chapter) 2. Disconnect all fixing clips (arrows) around the perimeter of the rear seat cushion cover, as shown in the...